Stuck 30m1 brass
Moderator: dromia
Forum rules
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
All handloading data posted on Full-Bore UK from 23/2/2021 must reference the published pressure tested data it was sourced from, posts without such verification will be removed.
Any existing data without such a reference should be treated as suspect and not used.
Use reloading information posted here at your own risk. This forum (http://www.full-bore.co.uk) is not responsible for any property damage or personal injury as a consequence of using reloading data posted here, the information is individual members findings and observations only. Always verify the load data and be absolutely sure your firearm can handle the load, especially older ones. If in doubt start low and work your way up.
Re: Stuck 30m1 brass
Just use the Lee lube as is. Put a dollop on a felt pad spread it out and roll your cases in it. You just need a thin film then resize. Wipe the lube off after re sizing.
-
bradaz11
- Full-Bore UK Supporter
- Posts: 4791
- Joined: Mon Jun 02, 2014 1:23 am
- Home club or Range: The tunnel at Charmouth, BWSS
- Location: Bristol
- Contact:
Re: Stuck 30m1 brass
Do I need to do the entire side of the case? Or just top 1/4 inch
Sent from my pink toy using "An application"
Sent from my pink toy using "An application"
When guns are outlawed, only Outlaws will have guns
Re: Stuck 30m1 brass
Just roll the case in it coat the whole of the outside of the case from rim to the base.You only need a very light coating. Once it transfers onto the die things willl get easier.
-
bradaz11
- Full-Bore UK Supporter
- Posts: 4791
- Joined: Mon Jun 02, 2014 1:23 am
- Home club or Range: The tunnel at Charmouth, BWSS
- Location: Bristol
- Contact:
Re: Stuck 30m1 brass
Thank you. I'll give that a go Monday
Sent from my pink toy using "An application"
Sent from my pink toy using "An application"
When guns are outlawed, only Outlaws will have guns
-
Mattnall
- Full-Bore UK Supporter
- Posts: 2943
- Joined: Wed Mar 06, 2013 5:32 pm
- Home club or Range: NRA, Redricks TSC, BS1944RC, HRA
- Location: East Herts
- Contact:
Re: Stuck 30m1 brass
Not too hard:bradaz11 wrote:..Also is IPA still stupid hard to get? As I've only got a small tin of it
..
IPA 99.9%
Arming the Country, one gun at a time.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
Good deals with Paul101, Charlotte the flyer, majordisorder, Charlie Muggins, among others. Thanks everybody.
-
WelshShooter
- Full-Bore UK Supporter
- Posts: 1813
- Joined: Wed Jun 25, 2014 9:45 pm
- Contact:
Re: Stuck 30m1 brass
IPA can be bought on ebay at pre pandemic prices now. Bought 1L of 99% for around £8 on ebay a month or so ago.
Who is online
Users browsing this forum: No registered users and 3 guests