Another Problem!
Moderator: dromia
Re: Another Problem!
phaedra...shhhhh :shifty:
Political Correctness is the language of lies, written by the corrupt , spoken by the inept!
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Another Problem!
Chuck, I will say nothing 
R.G.C., Yes it is/was perfectly free, only used it a few times since it was fitted in March.
The bolt etc. is kept perfectly clean and always has a very light lube applied after being cleaned.
R.G.C., Yes it is/was perfectly free, only used it a few times since it was fitted in March.
The bolt etc. is kept perfectly clean and always has a very light lube applied after being cleaned.
There's room for all Gods creatures, next to the mash and gravy :)
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Another Problem!
Heard back from Jeremy at Viking Arms (UK Distributor), they are collecting it for repair.
There's room for all Gods creatures, next to the mash and gravy :)
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Another Problem!
He's a pretty genuine guy - Viking Arms have always been reasonable with me in our dealings.phaedra1106 wrote:Heard back from Jeremy at Viking Arms (UK Distributor), they are collecting it for repair.
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
dodgyrog
- Posts: 4103
- Joined: Wed Jan 05, 2011 11:17 pm
- Home club or Range: Three Counties Sporting Club & Gardners Guns
- Location: Consett, County Durham
- Contact:
Re: Another Problem!
I had another thought! Don't take up another sport like sailing! :lol:
Purveyor of fine cast boolits.
All round good guy and VERY grumpy old man.
All round good guy and VERY grumpy old man.
-
Blackstuff
- Full-Bore UK Supporter
- Posts: 7852
- Joined: Sun Nov 07, 2010 1:01 pm
- Contact:
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Another Problem!
Just the usual CCI, they'd have to be made out of compressed Rottweilers to be able to snap a pin?
There's room for all Gods creatures, next to the mash and gravy :)
-
phaedra1106
- Posts: 3429
- Joined: Wed Feb 08, 2012 9:37 pm
- Location: Just outside Sacriston (the nice bit!)
- Contact:
Re: Another Problem!
Posted a question about the pins to Henry in the US and got a reply back pretty quickly!
They reckon it may have missed the heat treatment but would be unusual for 2 to have missed it. Could also be a problem with European primers (esp. S&B) being harder than Win or Rem, again unlikely as I don't shoot factory ammo and all I have used is CCI and Magtech standard LP primers.
Anyway, he has offered to send me the parts, not sure if they will ship directly to me here or have to go to Florida again.
Meanwhile I'll let Viking take a look at it and see if there's anything off with it, maybe the pins were short and the shaft was hitting the inside of the bolt face?.
EDIT
They are fast!, replied while I was typing this!. Couple of spares being put in the mail to me here, first class service!!
They reckon it may have missed the heat treatment but would be unusual for 2 to have missed it. Could also be a problem with European primers (esp. S&B) being harder than Win or Rem, again unlikely as I don't shoot factory ammo and all I have used is CCI and Magtech standard LP primers.
Anyway, he has offered to send me the parts, not sure if they will ship directly to me here or have to go to Florida again.
Meanwhile I'll let Viking take a look at it and see if there's anything off with it, maybe the pins were short and the shaft was hitting the inside of the bolt face?.
EDIT
They are fast!, replied while I was typing this!. Couple of spares being put in the mail to me here, first class service!!
There's room for all Gods creatures, next to the mash and gravy :)
Re: Another Problem!
As it should be..good advert for them for sure...SERVICE..What we should expect all the time.
Political Correctness is the language of lies, written by the corrupt , spoken by the inept!
-
R.G.C
Re: Another Problem!
Should they had 'missed' heat treatment, the FP would have bent prior to breaking and friction scratches along the FP tip diameter would have appeared...phaedra1106 wrote:Posted a question about the pins to Henry in the US and got a reply back pretty quickly!
They reckon it may have missed the heat treatment but would be unusual for 2 to have missed it. Could also be a problem with European primers (esp. S&B) being harder than Win or Rem, again unlikely as I don't shoot factory ammo and all I have used is CCI and Magtech standard LP primers.
Anyway, he has offered to send me the parts, not sure if they will ship directly to me here or have to go to Florida again.
Meanwhile I'll let Viking take a look at it and see if there's anything off with it, maybe the pins were short and the shaft was hitting the inside of the bolt face?.
EDIT
They are fast!, replied while I was typing this!. Couple of spares being put in the mail to me here, first class service!!
The "excuse" is not in favor of their QC procedures.....
R.G.C
Who is online
Users browsing this forum: No registered users and 3 guests